Radye Temel Tünel Kalıp
(27.6.14) Bosch Power Tools
OBJ_BUCH-783-007.book Page 5 Friday, June 27, 2014 9:29 AM
29
Service Do not use high speed steel (HSS) saw blades. Such saw
Have your power tool serviced by a qualified repair per- blades can easily break.
son using only identical replacement parts. This will en- Do not touch the saw blade after working before it has
sure that the safety of the power tool is maintained. cooled. The saw blade becomes very hot while working.
Never operate the machine without the insert plate.
Safety Warnings for Table Saws
Replace a defective insert plate. Without flawless insert
Never stand on the power tool. Serious injuries can occur plates, injuries are possible from the saw blade.
when the power tool tips over or when inadvertently com-
Check the cable regularly and have a damaged cable re-
ing into contact with the saw blade.
paired only through an authorised customer service
Take care that the blade guard operates properly and agent for Bosch power tools. Replace damaged exten-
can move freely. Always adjust the blade guard in such a sion cables. This will ensure that the safety of the power
manner that it faces loosely against the workpiece when tool is maintained.
sawing. Never clamp the blade guard when it is open.
Store the machine in a safe manner when not being
Never reach behind the saw blade in order to hold the used. The storage location must be dry and lockable.
workpiece, remove saw dust/wood chips or for any oth- This prevents the machine from storage damage, and from
er reason. The clearance of your hand to the rotating saw being operated by untrained persons.
blade is too small.
Never leave the machine before it has come to a complete
Guide the workpiece against the saw blade only when the stop. Cutting tools that are still running can cause injuries.
machine is switched on. Otherwise there is damage of kick-
Never use the machine with a damaged cable. Do not
back, when the saw blade becomes wedged in the work-
touch the damaged cable and pull the mains plug when
piece.
the cable is damaged while working. Damaged cables in-
Keep handles dry, clean, and free from oil and grease. crease the risk of an electric shock.
Greasy, oily handles are slippery causing loss of control.
Products sold in GB only: Your product is fitted with a
Operate the power tool only when the work area to the BS 1363/A approved electric plug with internal fuse (ASTA
workpiece is clear of any adjusting tools, wood chips, approved to BS 1362).
etc. Small pieces of wood or other objects that come in If the plug is not suitable for your socket outlets, it should be
contact with the rotating saw blade can strike the operator cut off and an appropriate plug fitted in its place by an author-
with high speed. ised customer service agent. The replacement plug should
Only saw one workpiece at a time. Workpieces placed on have the same fuse rating as the original plug.
top or aside of each other can cause the saw blade to jam or The severed plug must be disposed of to avoid a possible
the workpieces to move against each other while sawing. shock hazard and should never be inserted into a mains sock-
Always use the parallel guide or the angle guide. This et elsewhere.
improves the cutting accuracy and reduces the possibility Products sold in AUS and NZ only: Use a residual current de-
of saw blade binding. vice (RCD) with a rated residual current of 30 mA or less.
Use the machine for grooving or rebating only with an
appropriately suitable protective device (e. g. a tunnel Symbols
blade guard). The following symbols can be important for the operation of
Do not use the machine for cutting slots (stopped your power tool. Please memorise the symbols and their
grooves). meanings. The correct interpretation of the symbols helps
you operate the power tool better and more secure.
Use the machine only for cutting the materials listed
under Intended Use. Otherwise, the machine can be sub- Symbols and their meaning
ject to overload. Wear a dust respirator.
If the saw blade should become jammed, switch the ma-
chine off and hold the workpiece until the saw blade
comes to a complete stop. To prevent kickback, the
workpiece may not be moved until after the machine
has come to a complete stop. Correct the cause for the Wear safety goggles.
jamming of the saw blade before restarting the machine.
Do not use dull, cracked, bent or damaged saw blades.
Unsharpened or improperly set saw blades produce narrow
kerf causing excessive friction, blade binding and kickback.
Always use blades with correct size and shape (dia- Wear ear protectors. Exposure to
mond versus round) of arbour holes. Blades that do not noise can cause hearing loss.
match the mounting hardware of the saw will run eccentri-
cally, causing loss of control.