Revine Official Şikayet Var
25
The requirement for a correct area calculation is that the first ured values (7), select the desired entry and confirm it by
measured length (for example the ceiling height A) is pressing the results button (6).
identical for all sub-areas.
Deleting measured values
Grade measurement (see figure G) Briefly pressing the button (8) will delete the last measured
Press the button for grade measurement (3) to bring up the value in all measuring functions. Repeatedly pressing the
indicator for grade measurement on the display. The rear button briefly will delete the individual measured values in
of the measuring tool serves as the reference level. Press the reverse order.
button for grade measurement (3) again to use the sides of To delete the currently displayed entry in the list of meas-
the measuring tool as a reference level and rotate the display ured values, briefly press the button (8). To delete the com-
view by 90°. plete list of measured values and the constant "CST", press
Press the measuring button (2) to fix the measured value and hold the measured value list button (7) and at the same
and transfer it to the measured value memory. Press the time briefly press the button (8).
measuring button (2) again to continue the measurement. In the wall area measurement function, a brief first press of
If the display flashes during measurement, the measuring the button (8) will delete the last individual measured value;
tool has been tipped too heavily to the side. a second press will delete all lengths BX; a third will delete
If the "digital spirit level" function is activated in the basic the ceiling height A.
settings, the grade value is also displayed in the other meas-
Adding measured values
uring functions in line (d) of the display (1).
To add measured values together, first perform any meas-
Timer function urement or select an entry from the list of measured values.
The timer function is useful when the measuring tool should Next, press the plus button (11). "+" will appear on the dis-
be kept stationary during measurement, for example. play as confirmation. Then perform a second measurement
Press and hold the button for the timer function (6) to bring or select another entry from the measured value list.
up the indicator on the display. Press the results button (6) to retrieve the sum
The time period between triggering the timer and starting of both measurements. The calculation is
measurement is displayed in the measured value line (a). shown in the measured value lines (a) and the
The time period can be set between 1–60 seconds by press- sum is displayed in the result line (c).
ing the plus button (11) or minus button (5). When the sum has been calculated, you can add more meas-
The measurement is made automatically after ured values or measured value list entries to this result if you
the set time period has expired. press the plus button (11) before each measurement. Press
The timer function can also be used for dis- the results button (6) to end the addition.
tance measurements within other measuring Information on addition:
functions (e.g. area measurement). It is not possible to add – Mixtures of length, area and volume values cannot be ad-
or subtract measuring results or carry out continuous meas- ded together. For example, if a length value and an area
urement. value are added together, "ERROR" will appear briefly on
List of the last measured values the display when the results button (6) is pressed. The
measuring tool will then switch back to the most recently
The measuring tool stores the last 20 measured values and
active measuring function.
their calculations and displays them in reverse order (with
the most recent measured value displayed first). – The result of a measurement (e.g. volume value) is always
added; for continuous measurements, the measured
To retrieve the saved measurements, press the
value displayed in the result line (c) is added. It is not
button (7). The result of the last measurement
possible to add individual measured values from the
appears on the display, along with the indic-
measured value lines (a).
ator for the measured values list (e) and with
storage space for the numbering of the dis- Subtracting measured values
played measurements. To subtract measured values, press the minus
If no further measurements are saved upon pressing the but- button (5); "-" will appear on the display as
ton (7) again, the measuring tool switches back to the last confirmation. The subsequent steps are the
measuring function. Press one of the buttons for the measur- same as for the "Adding measured values" sec-
ing functions to exit the list of measured values. tion.
To permanently save the currently displayed measured
length value as a constant, press and hold the button for the Practical advice
list of measured values (7) until "CST" is shown on the dis- General advice
play. An entry in the list of measured values cannot be retro- The reception lens (17) and the laser beam output (16)
spectively saved as a constant. must not be covered during the measuring process.
To use a measured length value in a measuring function (e.g. The measuring tool must not be moved during a measure-
area measurement), press the button for the list of meas- ment (with the exception of the continuous measurement
Bosch Power Tools 1 92A 55A () Bosch Power Tools
3 31
Caractéristiques techniques
Télémètre laser GLM 80 GLM 80+R 60
Référence 3 K72 3 K72
Mesure de distances
Portée (typique) 0,05–80 mA) 0,05–80 mA)
B)
Portée (typique, dans des conditions défavorables) 35 m 35 mB)
A)
Précision de mesure (typique) ±1,5 mm ±1,5 mmA)
B)
Précision de mesure (typique, dans des conditions défavo- ±2,5 mm ±2,5 mmB)
rables)
Plus petite unité d’affichage 0,1 mm 0,1 mm
Mesure indirecte de distances et niveau à bulle
Plage de mesure –60° – +60° –60° – +60°
Mesure d’inclinaison
Plage de mesure 0°–° (4x90°)C) 0°–° (4x90°)C)
D)E)
Précision de mesure (typique) 0,2° ±0,2°D)E)
Plus petite unité d’affichage 0,1° 0,1°
Généralités
Températures de fonctionnement –10 °C +50 °CF) –10 °C +50 °CF)
Températures de stockage °C +50 °C °C +50 °C
Plage de températures de charge admissibles +5 °C +40 °C +5 °C +40 °C
Humidité de l’air maxi 90 % 90 %
Hauteur d’utilisation maxi au-dessus de la hauteur de réfé- 2 m 2 m
rence
Degré d’encrassement selon CEI 2G) 2G)
Classe laser 2 2
Type de laser nm, < 1 mW nm, < 1 mW
Diamètre approx. du faisceau laser (à 25 °C)
– à une distance de 10 m 6 mmE) 6 mmE)
E)
– à une distance de 80 m 48 mm 48 mmE)
Précision de calibrage approx. du laser par rapport au boîtier
– à la verticale ±2 mm/mH) ±2 mm/mH)
H)
– à l’horizontale ±10 mm/m ±10 mm/mH)
Arrêt automatique après env.
– Laser 20 s 20 s
– Appareil de mesure (en l’absence de mesure) 5 min 5 min
Poids selon EPTA-Procedure 0,14 kg 0,14 kg
Dimensions 51 x x 30 mm 51 x x 30 mm
Indice de protection IP 54 (protection contre la IP 54 (protection contre la
poussière et les projections poussière et les projections
d’eau) d’eau)
Rail de mesure
Référence – 3 K79
Dimensions – 58 x x 30 mm
Accu Lithium-Ion Lithium-Ion
Tension nominale 3,7 V 3,7 V
Capacité 1,25 Ah 1,25 Ah